Filter 12 dB Multi-mode filter, in which the circuit of the SEM module is used, Cream-coloured front panel and black knobs, Width: 8HP 40.3 mm, Depth: 55 mm (measured from the rear of the front panel), Power...
Brigade device module Vintage edition, 4096 BBD stages, For the A-100 modular system, Black front panel, Width: 14 TE / HP, Depth: 60 mm, Power requirement: +80mA (+12V) / -60mA (-12V)
Brigade Device modules Vintage Edition, For BBD circuits with 2048 stages, For the A-100 modular system, Black front panel, Width: 14 TE / HP, Depth: 60 mm, Power requirement: +80mA (+12V) / -60mA (-12V)
Brigade device module Vintage edition, 1024 stages Bucket Brigade Device, For modular system A-100, Black front panel, Width: 14 TE / HP, Depth: 60 mm, Power requirement: +80mA (+12V) / -60mA (-12V)
Passive Multi-Connector Eight interconnected jacks can be split into 2 groups (solder bridge on the assembly side), Width: 2 HP, Vintage edition with black front plate
Dual Slew Limiter Vintage edition with black front plate, Contains two separate slew limiters, A limiter with one control for attack and release (0-10 seconds), A limiter with separate controls for attack and release,...
Voltage Controlled Clock Multiplier Multiplication factor can be controlled by control voltage or a regulator, Black front panel, Width: 4 HP, Depth: 35 mm, Power requirements: +50 mA (+12 V) / -0 mA (-12 V)
Analogue and Trigger Sequencer Vintage edition with black front plate, 2 Switch rows with 8 steps each, Euro rack format, Width: 50 HP, Depth: 40 mm, Power consumption: +80 mA (+12V)/ -20 mA (-12V)
Sequencer Controller Module Vintage edition with black front plate, Expansion module for A-155 (Article Nr 154958 ), Different operating modes, LED display, 8 or 16 sequencer steps, Controls up to 2x A-155 (2x A-155...
Dual sample and hold module Vintage edition with black front plate, Designed to produce 'staircase' voltages, Consists of two separate sample / hold circuits, Eurorack format, Width: 4 HP, Depth: 30 mm, Power...
Envelope Generator Parameters can be set independently, 3-Step switch for selecting the time range, Euro rack format, Width: 8 HP, Depth: 50 mm, Power requirements: +20 mA (+12V) / -20 mA (-12V), Black front panel
Mixer Module Mixers with logarithmic potentiometers, Primarily for mixing audio signals, Vintage edition with black front panel, Width: 8 HP, Depth: 35 mm, Current consumption: +10mA (+12V) / -10mA (-12V)
Dual linear/exponential VCA The character of the control scale can be switched to linear or exponential, Can be used to process both audio and control voltages, Black front panel, Width: 8 HP, Depth: 50 mm, Power...
24 dB Low Pass 1 (VCF1)Module A-120 is a voltage-controlled 24 dB low-pass filter, which filters out the high frequency components from a sound spectrum while allowing the low frequencies to pass unhindered. The cut-off...
USB/ MIDI-CV/ Gate Interface Vintage edition with black front plate, Allows the integration of the A-100 module system into a USB or MIDI system, 4 Analogue CVs, Gate signal, Width: 6 HP, Depth: 55 mm, Power...
Bus Board Compatible with the Roland AIRA series (requires PSU3 power supply), Bus board (1x), Incl. 4 connection cables with flat connectors, approx. 30 cm in length
Substructure housing for modules 2x 84 HP, With PSU3 power supply: +12 V / 2000 mA, -12 V / 1200 mA, +5 V / 4000 mA, 100 - 230 V, Removable lid with carrying handle, Steel ball corners, Max. depth for modules in the...
Low cost base With PSU3 power supply (+ 12V / 2000 mA, -12V / 1200 mA, +5V / 4000 mA, 100 - 230 V), Two module rows, 2x 3 U / 84 HP, Ideal as a base for the A-100LC6 / LC9 or as stand-alone housing, External...
Base frame in the case Three rows with 84 HP each for the installation of modules, 3x 3 H3, Usable depth for A-100 modules: approx. 70 mm in the power supply area (lower right), otherwise approx. 100 mm, Dimensions (W...
Case with base frame Two rows with 84 HP each for installing modules, 2x 3 H3, Dimensions: approx. 465 x 330 x 170 mm, Usable depth for A-100 modules: approx. 70 mm in the power supply area (lower right), otherwise...
Original Doepfer case Untreated (no paint and/or lacquer) body constructed from "raw" wood, External dimensions: approx. 445 x 275 x 160 mm, Interior dimensions: approx. 2x 84 HP x 3 U, Usable depth for A-100 modules:...'
Analogue Modular System - Portable Suitcase Version Basic system with PSU3 power supply (12V / 2000mA, 12V / 1200mA 100 - 230 V), Installed modules and bus boards, Overall dimensions (W x H x D - with lid and rubber...
Case for A-100 module 9U with three module rows, External dimensions (W x H x D): Approx. 445 x 420 x 160 mm, Internal dimensions (W x H x D): 3 x 84 HP x 3 U, Usable depth for A-100 modules: About 80 mm in the area of...
Power Adapter 12 V / 2000 mA, -12 V / 1200 mA, 5 V / 4000 mA, 100-230 V ATTENTION - the connection and installation of parts which carry mains voltage (mains input, power supply, connecting cable, etc.) must only be...
Six Stage Opto FET VCF New filter module in which so-called opto FETs are used to control the filter frequency, Dimensions (W x D): 40.3 mm (8 HP) x 65 mm, Power requirement: 40 mA
Wasp Filter Special edition, Special 12 dB multimode filter, Circuit technology of the "EDP Wasp", Black front, Yellow pot caps, Width: 8 HP, Depth: 45 mm, Power requirements: +30 mA (+12 V)/-10 mA (-12 V)'
Case for Modules A number with 84 HP for installation of modules, Incl. external power supply (1200 mA) and bus board, Dimensions (W x H x D): approx. 445 x 150 x 160 mm
Passive Multi-Port Distributor 8x Interconnected jacks, Sockets are divided into 2x quadruple groups- but can also be modified to an eight-multiple (soldering bridge on the circuit board), Width: 2HP
Dual CV/ Gate to MIDI/ USB Interface Two independent CV/ Gate-to-MIDI/ USB interfaces, Each interface with 4 inputs (Gate, CVN, CVV, CVC), MIDI in/ out, USB, Euro rack format, Width: 10 HP, Depth: 55 mm, Power...
S-Trigger Cable With built-in S-trigger electronics, Length: 1.2 m, 3.5 mm Mono mini jack plug to 1/4" mono jack, Converts gate to switched trigger (S-trigger)'